home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
QRZ! Ham Radio 13
/
QRZ Ham Radio Callsign Database - Volume 13.iso
/
modfiles
/
ic_u16.txt
< prev
next >
Wrap
Text File
|
1999-04-07
|
5KB
|
109 lines
Subject: Icom U16 mod
From: n1ist@netcom.com (Michael L. Ardai)
In article <3omjss$rhl@news.rain.org>, leigh@rain.org () says:
>
>I'm trying to help a friend program ham frequencies into a newly acquired
>Icom U16 HT. It has a few commercial freqs in it.
>
>Thus far we can't change the commercial channels. I FTPed a U16 file
>from the oak.oakland.edu radio mod database, which seems to contradict
>itself. (It is listed below.)
>
>Questions:
>
>The file implies that the U16 must have a jumper in a certain spot, in
>order for it to be user-programmable. Where should this jumper be?
3/4 way down the left side of the logic board which is inside the front cover.>
>The file contradicts itself: when a new frequency is being inserted,
>should it be entered as five or six digits?
The frequency must be inserted in six digits. The decimal point must return
to be a valid frequency entry. Also you must hold the function button while entering the frequency and
then press enter before releasing the function buttion.
>What are the keystrokes required to enter a typical ham 70cm repeater?
>We can't get it to accept a new frequency using the data below...
>
>Thanks in advance and 73 from Leigh/KM6JE in Santa Barbara.
>--------------------------------------------------------------
>copied from the Internet:
>From: rosenblg@cmcl2.nyu.edu (Gary J. Rosenblum)
>Subject: how to program the ICOM-U16
>-------------------------------------------------------------------------
>
>If the U16 has been made programmable by moving a jumper:
>
>Try holding FUNCT down and entering 159357.
>It's now in prog mode. Exit with FUNCT-CLR.
>Function + 159357 (Enter program mode)
if the jumper has been removed a colon will now show up between the Ch and channel number
ex Ch 01 with jumper removed Ch:01. You have only 30 seconds time between
entries or the radio will time out and return to operation mode.
>Function + 1 Encoder tones (1-37) 1=67.0,2=71.9,3=74.4,4=77.0,5=79.7,
> 6=82.5,7=85.4,8=88.5,9=91.5,10=94.8,
> 11=100.0,12=103.5,13=107.2,14=110.9,
> 15=114.8,16=118.8,17=123.0,18=127.3,
> 19=131.6,20=136.5,21=141.3,22=146.2,
> 23=151.4,24=156.7,25=162.2,26=167.9,
> 27=173.8,28=179.9,29=186.2,30=192.8?,
> 31=203.5,32=210.7,33=218.1,34=225.7,
> 35=233.6,36=241.8,37=250.3
>
> + 2 Decoder tones (1-37)
>
> + 3 ?
>
> + 4 Delta + / Delta - offset, 5 digits
>
> + 5 Frequency, 5 digits (400MHz +)
>
> + 6 ?
>
> + 7 Sch. Ch. numbers. Allows alias ch numbers.
>
> + 8 Transmit timeout enable.
>
> + 9 TI, Transmit Inhibit
>
> + SCAN Priority Scan/Ch Scan
>
> + S.CH Channel Masking
>
> + CLEAR End progamming mode
>
>---------------------------------------------------------------------------
>Channel select: Standard method (up/down arrows or CH# + [ENTER])
>Frequency: Hold [FUNC], Press [5], enter 6 dig freq, [ENTER], release
> [FUNC]
>Rx CTCSS: Hold [FUNC], Press [2], enter 2 dig code, [ENTER], release
> [FUNC]
>Tx CTCSS: Hold [FUNC], Press [1], enter 2 dig code, [ENTER], release
> [FUNC]
>Offset Freq: Hold [FUNC], Press [4], use [#] for up offset, [*] for
> down offset, then enter freq to offset by (ie: [#] [0] [0]
> [0] [0] [0] for no offset, [#] [0] [5] [0] [0] [0] for the
> standard +5MHz UHF offset), [ENTER]
>Timeout Timer: Hold [FUNC], [8], Release [FUNC]
>Tx Inhibit: Hold [FUNC], [9], Release [FUNC]
>Special Channel Number: Hold [FUNC], Press [7], enter the special
>channel number (17-99), [ENTER], Release [FUNC]l
>Data Transfer MASTER: Hold [FUNC], [BEEP], Release [FUNC]
>Data Transfer SLAVE: Hold [FUNC] with power off, turn on, release
>[FUNC]
>
>--
>Gary J. Rosenblum
>UNIX Systems Manager rosenblg@nyu.edu
>New York University gary@nyu.edu
>=========================================================================
>Note: I haven't tried or verified this, proceed at your own risk. And
>DO NOT transmit outside of legal bands for your license. WA2ISE
>/EX
>
>
>